By:Chris Bryant, CCIE #12933
To pass your BSCI exam and earn your CCNP certification, you've got to master route summarization. When you get to the BSCI level, actually breaking the routes down into binary strings and performing summarization is second nature to you. (If it isn't, get some more practice!) What makes CCNP / BSCI route summarization more difficult is just keeping the different protocol summarization commands straight!
RIP and EIGRP both perform route summarization at the interface level with the ip summary-address command. In the following example, R2 is running RIP and was sending four routes to R3, R3's table looked like this before summarization:
R3#show ip route rip
172.16.0.0/24 is subnetted, 4 subnets
R 172.16.8.0 [120/1] via 172.23.23.2, 00:00:02, Ethernet0
R 172.16.9.0 [120/1] via 172.23.23.2, 00:00:02, Ethernet0
R 172.16.10.0 [120/1] via 172.23.23.2, 00:00:02, Ethernet0
R 172.16.11.0 [120/1] via 172.23.23.2, 00:00:02, Ethernet0
By summarizing the routes and using the ip summary-address command, RIP advertises only the summary route to the downstream neighbor.
R2(config)#int ethernet0
R2(config-if)#ip summary-address rip 172.16.8.0 255.255.252.0
R3#clear ip route *
R3#show ip route rip
172.16.0.0/22 is subnetted, 1 subnets
R 172.16.8.0 [120/1] via 172.23.23.2, 00:01:24, Ethernet0
EIGRP works much the same way, except that the EIGRP AS number must be named in the ip summary-address command.
In the following example, R2 was advertising four separate routes to R3 via EIGRP 100: 100.0.0.0, 101.0.0.0, 102.0.0.0, and 103.0.0.0, all with an eight-bit mask. What summary route can be used here?
The summary is 100.0.0.0 252.0.0.0. To send that route to downstream routers, configure the following on R2:
R2(config)#interface ethernet0
R2(config-if)#ip summary-address eigrp 100 100.0.0.0 252.0.0.0
R3 will then have only one route in its EIGRP table - the summary route.
R3#show ip route eigrp
D 100.0.0.0/6 [90/2297856] via 172.23.23.2, 00:02:33, Ethernet0
By mastering basic binary skills and keeping in mind that RIP and EIGRP perform route summarization at the interface level, you're one step closer to passing your BSCI exam and earning your CCNP certification!
In the next part of this tutorial, we'll take a detailed look at the different methods OSPF uses for route summarization.
To pass your BSCI exam and earn your CCNP certification, you've got to master route summarization. When you get to the BSCI level, actually breaking the routes down into binary strings and performing summarization is second nature to you. (If it isn't, get some more practice!) What makes CCNP / BSCI route summarization more difficult is just keeping the different protocol summarization commands straight!
RIP and EIGRP both perform route summarization at the interface level with the ip summary-address command. In the following example, R2 is running RIP and was sending four routes to R3, R3's table looked like this before summarization:
R3#show ip route rip
172.16.0.0/24 is subnetted, 4 subnets
R 172.16.8.0 [120/1] via 172.23.23.2, 00:00:02, Ethernet0
R 172.16.9.0 [120/1] via 172.23.23.2, 00:00:02, Ethernet0
R 172.16.10.0 [120/1] via 172.23.23.2, 00:00:02, Ethernet0
R 172.16.11.0 [120/1] via 172.23.23.2, 00:00:02, Ethernet0
By summarizing the routes and using the ip summary-address command, RIP advertises only the summary route to the downstream neighbor.
R2(config)#int ethernet0
R2(config-if)#ip summary-address rip 172.16.8.0 255.255.252.0
R3#clear ip route *
R3#show ip route rip
172.16.0.0/22 is subnetted, 1 subnets
R 172.16.8.0 [120/1] via 172.23.23.2, 00:01:24, Ethernet0
EIGRP works much the same way, except that the EIGRP AS number must be named in the ip summary-address command.
In the following example, R2 was advertising four separate routes to R3 via EIGRP 100: 100.0.0.0, 101.0.0.0, 102.0.0.0, and 103.0.0.0, all with an eight-bit mask. What summary route can be used here?
The summary is 100.0.0.0 252.0.0.0. To send that route to downstream routers, configure the following on R2:
R2(config)#interface ethernet0
R2(config-if)#ip summary-address eigrp 100 100.0.0.0 252.0.0.0
R3 will then have only one route in its EIGRP table - the summary route.
R3#show ip route eigrp
D 100.0.0.0/6 [90/2297856] via 172.23.23.2, 00:02:33, Ethernet0
By mastering basic binary skills and keeping in mind that RIP and EIGRP perform route summarization at the interface level, you're one step closer to passing your BSCI exam and earning your CCNP certification!
In the next part of this tutorial, we'll take a detailed look at the different methods OSPF uses for route summarization.
Article Source: http://www.redsofts.com/articles/
Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage, home of free CCNP and CCNA tutorials, The Ultimate CCNA Study Package, and Ultimate CCNP Study Packages.
For a FREE copy of his latest e-books, “How To Pass The CCNA” and “How To Pass The CCNP”, just visit the website! You can also get FREE CCNA and CCNP exam questions every day! Get your CCNP certification with The Bryant Advantage!
More Articles from Computer Certification Category:
Cisco CCNP / BCMSN Exam Tutorial: Dynamic VLANs and VMPS
Cisco CCNP / BSCI Certification: The BGP Attribute “MED”
Cisco CCNP / BSCI Tutorial: Route Summarization With RIP And EIGRP
Cisco CCNA Certification: The Importance Of Hands-On Practice
Passing Your MCSE Exams On The Road To Microsoft Certification
Cisco CCNA Certification Exam Tutorial: Configuring And Troubleshooting VTP
Cisco CCNP Certification / BCMSN Exam Tutorial: Writing QoS Policy
Cisco Certification: Putting Together Your Own Home Practice Lab
Cisco Home Lab Tutorial: Buying And Building A Frame Relay Switch
Cisco CCNA Exam Tutorial And Case Study: VLANs and IP Connectivity
Cisco CCNA Exam Tutorial: Five ISDN Details To Remember
Cisco CCNA / CCNP Home Lab Setup: How To Configure Reverse Telnet
Cisco CCNA Certification: Defining And Creating Collision Domains
Securing Your Network And Your Career With Cisco's CCSP Certification
Cisco CCNP / BSCI Exam Tutorial: Configuring And Troubleshooting OSPF Virtual Links
|
