By:Chris Bryant, CCIE #12933
Passing the CCNA is tough, and one of the toughest parts is keeping all the acronyms straight! Frame Relay has plenty of those, and today we're going to examine what DLCIs do and how they're mapped on a Cisco router.
Frame Relay VCs use Data-Link Connection Identifiers (DLCI - pronounced "del-see") as their addresses. Unlike other Cisco technologies, VCs have only a single DLCI in their header. They do not have a source and destination.
DLCIs have local significance only. DLCI numbers are not advertised to other routers, and other routers can use the same DLCI numbers without causing connectivity issues.
Cisco uses the term global addressing to describe a technique by which a router in a frame relay network is reached via the same DLCI number from each router in the network. For example, in a 25-router network, the same DLCI number would be used to reach “Router A” by each router.
Global Addressing is an organizational tool that does not affect the fact that DLCIs have local significance only.
The locally significant DLCI must be mapped to the destination router’s IP address. There are two options for this, Inverse ARP and static mapping.
In both of the following examples, the single physical Serial interface on Router 1 is configured with two logical connections through the frame relay cloud, one to Router 2 and one to Router 3.
Inverse ARP runs by default once Frame Relay is enabled, and starts working as soon as you open the interface. By running show frame-relay map after enabling Frame Relay, two dynamic mappings are shown on this router. If a dynamic mapping is shown, Inverse ARP performed it.
R1#show frame map
Serial0 (up): ip 200.1.1.2 dlci 122(0x7A,0x1CA0), dynamic,
broadcast,, status defined, active
Serial0 (up): ip 200.1.1.3 dlci 123(0x7B,0x1CB0), dynamic,
broadcast,, status defined, active
Static mappings require the use of a frame map statement. To use static mappings, turn Inverse ARP off with the no frame-relay inverse-arp statement, and configure a frame map statement for each remote destination that maps the local DLCI to the remote IP address. Frame Relay requires the broadcast keyword to send broadcasts to the remote device.
R1#conf t
R1(config)#interface serial0
R1(config-if)#no frame-relay inverse-arp
R1(config-if)#frame map ip 200.1.1.2 122 broadcast
R1(config-if)#frame map ip 200.1.1.3 123 broadcast
The syntax of the frame map statement maps the remote IP address to the local DLCI.
Broadcasts will not be transmitted by default; the broadcast option must be configured.
R1#show frame map
Serial0 (up): ip 200.1.1.2 dlci 122(0x7A,0x1CA0), static,
broadcast,
CISCO, status defined, active
Serial0 (up): ip 200.1.1.3 dlci 123(0x7B,0x1CB0), static,
broadcast,
CISCO, status defined, active
Hands-on practice is the best way to prepare for CCNA exam success. Working with Frame Relay in a lab environment practically guarantees that you'll truly master the concepts shown here - and then you're on your way to the CCNA and becoming a master network engineer.
Passing the CCNA is tough, and one of the toughest parts is keeping all the acronyms straight! Frame Relay has plenty of those, and today we're going to examine what DLCIs do and how they're mapped on a Cisco router.
Frame Relay VCs use Data-Link Connection Identifiers (DLCI - pronounced "del-see") as their addresses. Unlike other Cisco technologies, VCs have only a single DLCI in their header. They do not have a source and destination.
DLCIs have local significance only. DLCI numbers are not advertised to other routers, and other routers can use the same DLCI numbers without causing connectivity issues.
Cisco uses the term global addressing to describe a technique by which a router in a frame relay network is reached via the same DLCI number from each router in the network. For example, in a 25-router network, the same DLCI number would be used to reach “Router A” by each router.
Global Addressing is an organizational tool that does not affect the fact that DLCIs have local significance only.
The locally significant DLCI must be mapped to the destination router’s IP address. There are two options for this, Inverse ARP and static mapping.
In both of the following examples, the single physical Serial interface on Router 1 is configured with two logical connections through the frame relay cloud, one to Router 2 and one to Router 3.
Inverse ARP runs by default once Frame Relay is enabled, and starts working as soon as you open the interface. By running show frame-relay map after enabling Frame Relay, two dynamic mappings are shown on this router. If a dynamic mapping is shown, Inverse ARP performed it.
R1#show frame map
Serial0 (up): ip 200.1.1.2 dlci 122(0x7A,0x1CA0), dynamic,
broadcast,, status defined, active
Serial0 (up): ip 200.1.1.3 dlci 123(0x7B,0x1CB0), dynamic,
broadcast,, status defined, active
Static mappings require the use of a frame map statement. To use static mappings, turn Inverse ARP off with the no frame-relay inverse-arp statement, and configure a frame map statement for each remote destination that maps the local DLCI to the remote IP address. Frame Relay requires the broadcast keyword to send broadcasts to the remote device.
R1#conf t
R1(config)#interface serial0
R1(config-if)#no frame-relay inverse-arp
R1(config-if)#frame map ip 200.1.1.2 122 broadcast
R1(config-if)#frame map ip 200.1.1.3 123 broadcast
The syntax of the frame map statement maps the remote IP address to the local DLCI.
Broadcasts will not be transmitted by default; the broadcast option must be configured.
R1#show frame map
Serial0 (up): ip 200.1.1.2 dlci 122(0x7A,0x1CA0), static,
broadcast,
CISCO, status defined, active
Serial0 (up): ip 200.1.1.3 dlci 123(0x7B,0x1CB0), static,
broadcast,
CISCO, status defined, active
Hands-on practice is the best way to prepare for CCNA exam success. Working with Frame Relay in a lab environment practically guarantees that you'll truly master the concepts shown here - and then you're on your way to the CCNA and becoming a master network engineer.
Article Source: http://www.redsofts.com/articles/
Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage, home of free CCNA and CCNP tutorials, The Ultimate CCNA Study Package, and Ultimate CCNP Study Packages.
You can also join his RSS feed and visit his blog, which is updated several times daily with new Cisco certification articles, free tutorials, and daily CCNA / CCNP exam questions! Details are on the website.
For a FREE copy of his latest e-books, “How To Pass The CCNA” and “How To Pass The CCNP”, visit the website and download your free copies. You can also get FREE CCNA and CCNP exam questions every day! Get your CCNA study guide from The Bryant Advantage!
More Articles from Computer Certification Category:
Cisco CCNP / BCMSN Exam Tutorial: Dynamic VLANs and VMPS
Cisco CCNP / BSCI Certification: The BGP Attribute “MED”
Cisco CCNP / BSCI Tutorial: Route Summarization With RIP And EIGRP
Cisco CCNA Certification: The Importance Of Hands-On Practice
Passing Your MCSE Exams On The Road To Microsoft Certification
Cisco CCNA Certification Exam Tutorial: Configuring And Troubleshooting VTP
Cisco CCNP Certification / BCMSN Exam Tutorial: Writing QoS Policy
Cisco Certification: Putting Together Your Own Home Practice Lab
Cisco Home Lab Tutorial: Buying And Building A Frame Relay Switch
Cisco CCNA Exam Tutorial And Case Study: VLANs and IP Connectivity
Cisco CCNA Exam Tutorial: Five ISDN Details To Remember
Cisco CCNA / CCNP Home Lab Setup: How To Configure Reverse Telnet
Cisco CCNA Certification: Defining And Creating Collision Domains
Securing Your Network And Your Career With Cisco's CCSP Certification
Cisco CCNP / BSCI Exam Tutorial: Configuring And Troubleshooting OSPF Virtual Links
|
